Photocell start and stop
On the automatic version, the entrance sensor starts the spray cycle and the exit sensor stops it after the vehicle passes through.
Site Disinfection Gate – The Foundation of Effective Farm Biosecurity
Protect your livestock with the ALPHAVET Robotics automatic vehicle disinfection gate. Photocells start the disinfection cycle as a vehicle arrives and stop spraying after it passes through.
The Most Important Link in Biosecurity
Vehicles entering and leaving a livestock site can carry infectious diseases in or spread them further. Contamination can adhere to wheels, vehicle sides and the undercarriage.
The gate provides a consistent automatic disinfection cycle that helps reduce biosecurity risks associated with vehicle traffic.
- Vehicles entering and leaving a site can carry infectious diseases in or spread them further.
- Pathogens can easily enter the site on organic contamination attached to wheels, mudguards and the undercarriage.
- A consistent disinfection process helps reduce biosecurity risks associated with vehicle traffic.
Automatic Vehicle Detection and Disinfection Cycle
The unit is controlled by an Industrial Shields Ardbox Relay PLC. On the automatic version, entrance and exit photocells start and stop spraying; the controller also indicates an empty tank and faults, and includes an emergency stop switch.
Configured concentration
The dosing unit prepares the disinfectant solution at the pre-set concentration.
Status and fault indicators
The system indicates operating status, an empty tank and faults, and includes an emergency stop switch.
Operating lights
Indicator lights signal operation and system status.
Robust Design for Every Farm Environment
21-nozzle, multi-directional treatment
The system treats vehicles from the sides, above and below. Ramp-integrated nozzles help spray the undercarriage and wheel arches.
Automatic photocell cycle
An entrance photocell detects an approaching vehicle and starts spraying; an exit photocell stops the cycle after the vehicle leaves.
High-capacity pump
The configuration featured in the newsletter uses a pump capable of delivering approximately 60–70 litres of liquid per minute.
Selectable operation for open loads
With a solenoid-valve configuration, overhead spraying can be shut off to help keep open loads dry.
Stainless-steel structure
The gate frame is made of stainless-steel tubing. Nozzles are positioned to provide even treatment of the vehicle exterior.
IP65 protection
The IP65 rating stated in the documentation means complete dust protection and protection against water jets.
Winter configuration by specification
The optional heating package can include a heated frame, an insulated and heated machinery enclosure, and frost-protected pipework and nozzles. Confirm the exact configuration and operating temperature for each project.
Recommended disinfectant
The manufacturer recommends Perfect Kombicid barn and surface disinfectant. Set the dilution according to the disinfectant manufacturer’s instructions.
Choose the Gate That Fits Your Site Conditions
After selection, the exact configuration appears in the quote form so the next consultation can start with the right technical context.
A winter configuration can include a heated frame, an insulated and heated machinery enclosure, and frost-protected pipes and nozzles. Confirm the exact configuration and operating temperature when requesting a quote.
Installation Requirements
The installation described in the newsletter required a flat, load-bearing concrete base, a nearby 230 or 400 V connection matched to the selected configuration, and mains water. Confirm the exact electrical requirement and connection locations during the site survey.
Flat, load-bearing concrete base
230 V or 400 V power supply, depending on the selected configuration
Mains water supply nearby
Frequently Asked Questions
What vehicles can the ALPHAVET Robotics disinfection gate treat?
The technical documentation lists livestock transport trucks, feed transport and service vehicles, passenger cars, and other vehicles entering or leaving the site. Vehicle dimensions and the installation layout should be confirmed for each project.
How does the automatic disinfection cycle start and stop?
On the automatic version, an entrance photocell detects an approaching vehicle and starts spraying. An exit photocell stops the cycle after the vehicle leaves.
What frost-protection operation is specified in the technical documentation?
The documentation specifies a heating cable and heating element for ambient temperatures below 5°C. The minimum permitted outdoor temperature and the exact frost-protection configuration must be confirmed for the selected build.
Which disinfectant should be used?
The manufacturer’s documentation recommends Perfect Kombicid barn and surface disinfectant. Always set the concentration according to the disinfectant manufacturer’s dilution instructions.
What electrical connection is required?
The CE documentation specifies a nominal 230 V AC, single-phase, 50 Hz supply; the installation requirements in the newsletter mention a 230 or 400 V connection depending on configuration. Confirm the exact requirement during quotation. Electrical connection must be carried out by a suitably qualified electrician.
Request a Custom Quote
The form collects the key site information and selected gate type for the next consultation.
Current configuration4000 × 4000 mm clear opening - Automatic version with photocell vehicle detection